Product Description
$29.00
Set of six oversized pins.
All dropper posts require key way clearance. With so many different frames, clamps and ride heights it’s not possible to ship play-free without running the risk of binding. The kit is meant to remove additional play that might develop over time or, for the more mechanically inclined, to tune the play out for a specific bike.
Start with the 3 pins marked with 2 lines. If play still exists move to the 3 pins marked with 4 lines.
In stock
Description
Follow the instructions below referencing this exploded view
– With the post still installed on bike complete the following steps
– Remove the saddle and clamps
– Wipe away any dirt or debris
– Lower the post to mid travel
– Unthread mid cap assembly (8)
– Remove Cartridge lockring (6) with needle nose pliers
– Upper tube (7) will now slide out
– Replace guide pins (10) with oversized guide pins (19) or (20) and regrease
– Reassemble in reverse order
Related Products
Keep Your Ride Smooth And Reliable With The OneUp V2 Dropper Rebuild Kit
The V2.1 Dropper Rebuild Kit is an updated rebuild kit for the OneUp V2 Dropper Post with an updated midcap assembly and new ultra-low friction SKF® seals. This Kit does 30.9,31.6 and 34.9mm diameters Includes:- 1 x SKF® Midcap Assembly
- 1 x Upper Bushing
- 1 x Lower Bushing
- 3 x Brass Pins
SLS (Super Light Steel) springs are now available from FOX for DHX and VAN rear shocks. These SLS springs are a lighter weight steel spring option offered in addition to our standard steel springs. The new SLS springs from FOX are lighter than titanium springs at more affordable prices. A proprietary surface treatment and stress relief process removes residual stresses from the spring, allowing them to withstand higher stresses. Each spring is optimised by using a smaller wire diameter and fewer coils, creating a lighter spring.
All SLS springs are orange and are marked with their spring rate in lbs/in and the maximum travel of the shock that they are designed to be paired with.
$209.00 – $229.00
The V3 Dropper Remote is a lighter action remote with a replaceable rubber thumb pad and integrated cable port. Available in 7 colours, all major clamp standards and as a remote only option so you can reuse your existing V2 clamp. Includes cable and housing. It's the easiest way to upgrade any mechanical dropper.
$109.00
- 1x Remote body
- 1x Black thumb cushion (colours sold seperately)
- Cable, housing, cable end & barrel end
It is important to have the right tool for the job. It not only will make the job easier, but it will keep you from damaging costly parts. The Fox Shox Seal Driver Tool is designed to perfectly drive Fox fork wiper seals with ease. These drivers will work on both flanged seals and the new low friction seals without flanges.
Keep The Mud Off Your Fork And Out Of Your Eyes With The Official FOX Mud Guard Designed Specifically For FOX 36, 38
$39.00
- Genuine Fox Mud Guard for 2021
- Install in minutes!
- Available in Black to suit 2021 Fox 36 or 38 only.
- Part: 803-01-441
High-quality CNC machined dropper lever for any cable actuated dropper post that matches the aesthetics of Hope’s Brakes. The lever rotates on ball bearings for super smooth and precise action with minimal unwanted movement and features adjustable leverage with a 20% range of adjustment.
- CNC machined
- Smooth ball bearing actuation
- Adjustable leverage
- Adjustable reach
- Works with the majority of dropper posts
- Mounts directly to Hope master cylinders via a direct shifter mount for super clean look
- Mounts with any SRAM Matchmaker or bar clamp
Changing volume spacers in the shock is an internal adjustment that allows you to change the amount of mid stroke and bottom out resistance. By decreasing the volume in the air canister, the shock will ramp up more quickly at the end of its travel, resisting harsh bottom-outs while still providing small-bump compliance in the top of its travel. It is critical to follow Fox’s instructions and recommendations of which spacers to use.
$49.00
Replace the thru-axle on your front fork with this genuine Fox Shox replacement part. The Fox Racing Shox 15x100mm QR Thru Axle is compatible with all 32mm and 34mm Fox 15mm QR Forks.
Keep your suspension feeling new and prevent long term wear with a fresh set of seals from Racing Bros. These seals utilise graphite and Teflon to reduce friction. If you're in need of replacement seals, you'll be able to tell the difference immediately once you install these.
$29.00
The new Fox Inverted Fork
Podium is designed to be ridden like a downhill fork. No barriers. No hesitation. Complete confidence that your front wheel will hold the line, no matter how fast or how big you push it. All this while keeping your bike in a familiar range of travel and geometry in a single crown package.
• Wheel size: 29”
• Travel: 170mm
• Damper: GripX2
• Crown: 58HT
SHIMANO – Seat post Dropper Lever – I-SPEC EV
With ideal ergonomics and smooth lever action, SHIMANO’s SL-MT800-IL seat post dropper lever provides quick lever access with minimal hand movement. The new I-SPEC EV lever offers a wide range of adjustments and 7mm of cable stroke. With a lightweight and compact design, the SL-MT800-IL lever sets the standard for mountain bike dropper remotes.
- Fast & effortless operation
- Quick lever access from grip position with minimum hand movement
- Light operation effort
- Compatible with common dropper posts
- 7 mm cable stroke
- I-SPEC EV type only
Most Advanced Lightweight Trail Shock An entirely new base valve design and the addition of a valved circuit in open mode raises the already high bar for trail category performance. Factory Says It All The best-of-the-best technology we have to offer is available in our Factory Series models with our buttery smooth, and ultra durable Genuine Kashima Coat. These products have been proven on the Downhill World Cup Circuit. Key Highlights Are • NEW graphics • X2 small bump sensitivity meets DPS lightweight and simplicity • Recirculating oil damper design for more control • Remote option • One-piece EVOL air sleeve improves responsiveness and sensitivity • Three-position lever with adjustable Open Mode • Offers 10 clicks to fine-tune compression • Imperial and metric sizes • Factory Series models feature Genuine Kashima Coat • Starting Weight 398g (includes Igus bushings, but no mounting hardware)
210 X 52.5
$399.00
Add to cart
When you need to go really big, reach for the 38.
Optimized for 160-180mm of travel, the 38 redefines capability of a long travel single crown fork, setting a new benchmark for confidence, performance, and durability. Welcome to the big time. • Wheel size: 29” • Travel: 170mm • Damper: GripX2
